Pixhawk 2.1 Autopilot - Standard Set

$299.00
RRP $349.00
SAVE $50.00 (14%)
In Stock



Calculate Shipping


Get Started on your road to Autonomy! This Standard Kit contains the following items

  • Pixhawk 2.1 Cube.... the brains behind the operation.
  • Pixhawk 2.1 Standard Carrier Board (not compatible with Intel Edison Chip)
  • 1 x Power Brick (two power bricks can be fitted for redundant power.)
  • Cable set that allows you to connect to your old Telemetry module, GPS, and sensors
  • SD Card (inserted in Cube) 
  • 2 x Telem cables
  • Power Cable
  • I2C Cable
  • Buzzer Cable
  • Micro USB cable
  • GPS1 cable (with safety switch)
  • I2C Splitter
  • 4 x Mounting screws (M2.5*8)
  • 3M Double Sided Foam Tapes
  • To take full advantage of the Pixhawk 2.1, Please add the new GPS with built in Safety switch.

 

The goal with Pixhawk2 was not just to update Pixhawk but, to fundamentally redesign the entire experience while maintaining the independent, open-hardware design. Pixhawk2 is the world’s most advanced open autopilot system aimed at meeting the needs of the academic, hobby and industrial communities at low cost and high availability. Utilizing the advanced APM firmware, Pixhawk2 turns any remote controlled plane, copter, or rover into a full-featured professional drone.

The “Cube”
The Pixhawk2 has been designed for hobbyists and professionals alike. The “cube” is the center of that philosophy, providing all the functions expected from a modern autopilot with one simple interface. The 80pin DF17 connector seamlessly attaches to the carrier board for a complete standalone autopilot or can be used by OEM’s to design carrier boards for custom solutions.

Boasting triple redundant IMU’s with vibration isolation and built-in heat control for operation in low-temperature environments, the Pixhawk2 Cube is second to none.

The “Carrier”
All-in-one
An integrated, single board / box flight controller.
All-in-one design with integrated FMU and IO and lots of I/O ports.

Improved ease-of-use.

Improved sensor performance.

Improved microcontroller resources.

Increased reliability and reduced integration complexity.
Separate power supplies for FMU and IO (see power architecture section).
On-board battery backup for FMU and IO SRAM / RTC.

So much I/O
14 PWM ports, five general purpose serial ports, three analog inputs, two I2C ports, two CAN Bus interface ports and, an SPI port make Pixhawk2 more than capable for most applications without the need for expansion. This is broken out on the carrier board for use with; GPS, Telemetry, External USB, RGB LED and safety switch, airspeed sensors, CAN bus ESCs, power modules and much much more.

(PIX2-2.1-SET-STD)

SKU PIX2-2.1-SET-STD
Barcode # 512K00011-7300561
Brand Pixhawk 2
Shipping Weight 0.3360kg
Shipping Width 0.170m
Shipping Height 0.070m
Shipping Length 0.100m

Be The First To Review This Product!

Help other Rise Above users shop smarter by writing reviews for products you have purchased.

Write a product review


Others Also Bought


DJI FlameWheel F550 ARF Kit

DJI FlameWheel F550 ARF Kit

$499.00

6% OFF RRP $529.00
DJI DT7 Radio Controller (includes DR16 Receiver)
7% OFF RRP $269.00
Phobotic Centrepiece HV Gimbal Controller
15% OFF RRP $750.00
COBRA CM-2208 Multirotor Motor 2400kv
38% OFF RRP $40.00
WM610 gimbal guard

WM610 gimbal guard

Now $2.00

On Sale 60% OFF RRP $5.00

More From This Category