Scentroid DR1000 Air Quality Sampling Unit for Large Drone (5 sensors)




Calculate Shipping


 

The Scentroid DR1000 is a system developed to offer an innovative solution for the measurement of key environmental parameters, ie the quality of air we breathe. The Air Quality Sampling Unit consists of a flying laboratory to fit on a commercial drone (drone not included). It can be used to sample and analyze ambient air at heights of up to 150 meters above ground level that was previously impossible to accomplish. Air quality mapping, model verification, analysis of potentially dangerous sites are all made possible by this novel innovation.

Advantages

The Scentroid DR1000 introduces the unique advantage of measuring the presence of chemical pollutants, industrial processing of fumes and more in real time and with the advantage of mobility of the drone. You can then follow the default paths, or choose them according to the need of the hour. Another advantage of using the drone is that you can greatly reduce the risks to human operators, thus avoiding exposing them to potentially deadly agents.

How it works

The Scentroid DR1000 has five integrated chemical sensors that analyze the air at regular intervals (5/2), sending the information to the operator on the ground. The information is also stored in a memory in order to make subsequent mappings. See the Specifications tab for a full list of available sensors.

When the operator identifies the critical areas, or if you want measurements at particular locations (eg. Water tower), you can remotely control the filling of a plastic bag with air to make subsequent analysis in the laboratory. With tracings made along the way you can build a dynamic map (also three-dimensional) of the temporal evolution of the air pollutant dispersion.

Sensors

The Scentroid DR1000 uses up to five sensors of your choice, a full list can be found in the Specifications tab. Some measured in parts per million (ppm), others in parts per billion (ppb).

Real-time information

The Scentroid DR1000 is constantly connected with a ground station that collects real-time information. This allows the operator to understand the state of the situation in the air and if necessary take immediate decisions (ez. Sample the air with bag).

 

FLYING LABORATORY DR1000

The Scentroid DR1000 Air Quality Sampling Unit consists of a flying laboratory to fit on a commercial drone (drone not included). The DR1000 can be used to sample and analyze ambient air at heights of up to 150 meters above ground level that was previously impossible to accomplish. Air quality mapping, model verification, analysis of potentially dangerous sites are all made possible by this novel innovation.
 

Sampling from Hazardous Sources

With the DR1000 sampling drone operator can stay safely away from hazardous sources while acquiring environmental samples.


Direct Flare Plume Sampling

The DR1000 can be flown into the plume of a flare to take direct samples for analysis for chemical composition and olfactometery. Temperature and humidity of the plume are also measure to ease dispersion calculation.


Continuous Chemical Monitoring

Scentroid DR1000 air sampling drone is capable of providing remote monitoring of more than 50 chemicals. Data from on-board sensors are transmitted to operator’s tablet for to be viewed live and logged.

Improves Air Sampling Capability Over Difficult Terrain and at Different Heights
It is often necessary to sample stacks, ponds, and other location where human access is difficult and /or dangerous. Furthermore, operator exposure to dangerous chemicals during sampling must be carefully considered. The Scentroid sampling drone gas detector allows the operator to stay safely away from potentially hazardous sources while acquiring the required air sample for laboratory analysis. The sampling drone can also be used to sample ambient air at an elevation of up to 150 meters above ground level that was previously impossible to accomplish.

One Operator Can Handle Everything
The Scentroid DR1000 flying laboratory is a complete package that allows one person to fly the drone to take samples from all inaccessible and unreachable locations at the site, while monitoring the exact location of the drone including longitude, latitude, altitude and height via the Scentroid Drone Sampler Application residing on a customer supplied Android phone that is attached to the drone remote control via a supplied mount.

Continuous Chemical Monitoring
In addition to air sample bag collections, the Scentroid DR1000 flying laboratory is capable of providing up to five remote chemical sensors to monitor chemical concentration levels. Data from on-board sensors are transmitted to a customer supplied operator’s Android phone to be viewed live and logged. While in flight, every 2 seconds, the drone will record GPS positions, altitude, temperature, humidity, H2S, VOC, SO2, Methane, and any chemical that is being monitored. The data can be used to create a map of the emission plume in real-time.

How many liters is each sample bag?
The standard sample bag that is included is 3 Liters but larger ones up to 10 Liters can be ordered. (However be aware that the length of a  fully inflated 10 Litre bag may exceed past the landing gear of most drones.)


Is it possible to sample from a source under negative pressure?
Yes. Under 100 mbar the standard unit will operate with minimal dilution variance. Above 100 mbar specific calibration sheets are provided by Scentroid and should be used.

How do I proceed with an order?

To place an order, a 50% deposit is required. Lead time is approximately 5-weeks from time of order.

The price is for the Air Sampling System only, the drone is not included. If you're interested in integrating this system with a drone, please contact us for a quote.

 

(SCENT-DR1000-UNIT)

Maximum operating time with full charge battery - 10 hours
Time to fill up a sample bag    15 Sec per Liter
Weight    1135 g

Standard Sensors
Sensor ID Chemical Range Lowest Detection Threshold Resolution (ppm)
CD2 Carbon Dioxide – Low Concentration 0-5000 ppm 0 ppm 15 ppm
HS1 Hydrogen Sulfide (low Concentration – ppb) 1 ppm 3 ppb 1 ppb
MT1 Methane (LEL) 0-100 % LEL 0 ppm 1% LEL
PD1 Total VOCs (ppb) – PID 50 ppm ( isobutylene ) 0 ppm 1 (ppb isobutylene)
SD2 Sulfur Dioxide (low Concentration) 20 ppm 0 ppb 20 ppb
         
Available Sensors
Sensor ID Chemical Range Lowest Detection Threshold Resolution (ppm)
CD1 Carbon Dioxide – High Concentration 5,000 to 900,000 ppm 5000 ppm 100 ppm
CD2 Carbon Dioxide – Low Concentration 0-5000 ppm 0 ppm 15 ppm
CO1 Carbon Monoxide (low Concentration) 500 ppm 15 ppm 5 ppm
CO2 Carbon Monoxide (high concentration) 10000 ppm 250 ppm 20 ppm
C11 Chlorine 20 ppm 200 ppb 20 ppb
E1 Ethylene Oxide 0-100 ppm 1 ppm 0.1 ppm
H1 Hydrogen 0-5000 ppm 1 ppm 0.8 ppm
HCL1 Hydrogen Chloride 100 ppm 0.1 ppm 0.1 ppm
HCY1 Hydrogen Cyanide 100 ppm 0.1 ppm 0.1 ppm
AM1 Ammonia 100 ppm 0 ppm 1 ppm
ON1 Ozone and Nitrogen Dioxide O3- 20; NO2- 20 ppm 0 ppb 15 ppb
PH1 Phosphine (low Concentration) 10 ppm 0 ppm 30 ppb
PH2 Phosphine (high Concentration) 2000 ppm 5 ppm 2 ppm
HS1 Hydrogen Sulfide (low Concentration – ppb) 1 ppm 3 ppb 1 ppb
HS2 Hydrogen Sulfide (high Concentration – ppm) 2000 ppm 1 ppm 1 ppm
NO1 Nitrogen Oxide 100 ppm 0 ppm 0.1 ppm
CH1 Carbon Monoxide & Hydrogen Sulfide CO 0-1000, H2S 0-100 ppm 0 ppm CO 1, H2S 0.25 ppm
E2 Ethanol 0-500 ppm 0 ppm 1 ppm
MT1 Methane (LEL) 0-100 % LEL 0 ppm 1% LEL
NC1 Nitric Oxide (low Concentration) 20 ppm 0 ppm 80 ppb
NC2 Nitric Oxide (High Concentration) 5000 ppm 0 ppm 1 ppm
ND1 Nitrogen Dioxide (Low Concentration) 20 ppm 0 ppm 0.02 ppm
ND2 Nitrogen Dioxide (high Concentration) 200 ppm 0 ppm 0.1 ppm
O1 Oxygen 0-20% 0 ppm 0.10%
O2 Oxygen 0-100% 0 ppm 1%
PD1 Total VOCs (ppb) – PID 50 ppm ( isobutylene ) 0 ppm 1 (ppb isobutylene)
PD2 Total VOCs (ppm) – PID 300 ppm ( isobutylene ) 1 ppm 0.1 (ppm isobutylene)
SD1 Sulfur Dioxide (high Concentration) 2000 ppm 0 ppm 2 ppm
SD2 Sulfur Dioxide (low Concentration) 20 ppm 0 ppb 20 ppb
FM1 Formaldehyde 10 ppm 0.01 ppm 0.01 ppm
PM 1-10 Particulate PM 1, 2.5, 10 0-10,000 Particles/Sec PM 1 N/A
SKU SCENT-DR1000-UNIT
Brand Scentroid
Shipping Weight 10.0000kg

Be The First To Review This Product!

Help other Rise Above users shop smarter by writing reviews for products you have purchased.

Write a product review


Others Also Bought



More From This Category